Soffit Calculator

This works out how much soffit an eave takes: the area, the panels, the channel at the wall and at the fascia, and the fascia itself. Give it the eave run, the overhang width and the corner counts, or give it a house footprint and a roof type and it works the run out for you, including the rake on a gable end. Soffit is the ring between the wall line and the fascia line, so each outside corner adds an overhang-by-overhang square that measuring along the wall misses and each inside corner takes one back, and both are counted here. It also shows how the overhang divides into a panel, because an overhang that does not divide the panel length throws away part of every board before any waste allowance is applied. How much of the soffit needs to be vented is a ventilation question, not a material one, so the tool reports the net free area the vented share supplies and leaves the sizing to the attic.

Calculator Type
Measurements In
This moves the whole form. Runs are read in feet, overhangs and panel widths in inches, ventilation in square inches per foot, the prices per square foot and per lineal foot, and the pitch as a rise in 12. The answers come back the same way.
Lineal feet, or lineal metres if you switched above. Measured along the wall, adding every run that gets soffit. Corners are counted separately below.
Wall face to the back of the fascia, in inches. 12, 16, 18 and 24 in are the common ones.
Corners the soffit wraps around the outside of. A plain rectangle has four. Each one adds an overhang-by-overhang square that measuring along the wall misses.
Re-entrant corners, where an L or a U turns back on itself. Each one takes a square back off.
Cuts at corners and returns, and the pieces that end up too short to use. Ten percent suits a plain rectangle, fifteen or more a cut-up elevation with several returns.
Vinyl and aluminium soffit is usually stocked in 12 ft lengths, and blank takes that.
The width one panel covers once it is locked to the last one, off the carton. Commonly 12 in, sometimes 16 in, and blank takes 12 in.
Off the product sheet, in square inches per lineal foot, or square millimetres per metre if you switched above. Continuous perforated vinyl soffit runs around 9 sq in per lineal foot, which is 19,049 mm2 per metre; a fully vented panel can be more and a lightly perforated one much less. Leave it blank for that 9 sq in per foot. Enter 0 for solid board.
Widget
Measurements In
This moves the whole form. Runs are read in feet, overhangs and panel widths in inches, ventilation in square inches per foot, the prices per square foot and per lineal foot, and the pitch as a rise in 12. The answers come back the same way.
The long wall, measured at the footprint. On a gable roof this is the side the eave runs along.
The other wall. On a gable roof this is the span the ridge runs over.
How far the roof hangs past the gable end wall. Zero is a flush gable. This also lengthens the eave, because the eave runs the full length of the roof and not just the length of the wall. Ignored on a hip roof.
A rise in 12, or degrees if you switched to metres above. Only used for the rake, which runs up the slope and is therefore longer than its horizontal run. Left blank it is a 6 in 12, which is 26.6 degrees.
Cuts at corners and returns, and the pieces that end up too short to use. Ten percent suits a plain rectangle, fifteen or more a cut-up elevation with several returns.
Vinyl and aluminium soffit is usually stocked in 12 ft lengths, and blank takes that.
The width one panel covers once it is locked to the last one, off the carton. Commonly 12 in, sometimes 16 in, and blank takes 12 in.
Off the product sheet, in square inches per lineal foot, or square millimetres per metre if you switched above. Continuous perforated vinyl soffit runs around 9 sq in per lineal foot, which is 19,049 mm2 per metre; a fully vented panel can be more and a lightly perforated one much less. Leave it blank for that 9 sq in per foot. Enter 0 for solid board.
Widget